Fabrication of an electrolyte-supported protonic ceramic fuel cell with nano-sized powders of Ni-composite anode

Composite anodes of nano-sized Ni and Ba(Zr_0.85Y_0.15)O_3-δ (BZY) were fabricated by infiltrating a single precursor solution of BZY and Ni into the BZY scaffold, and decreasing the calcination temperature to 1173 K. This decrease in the fabrication temperature of the Ni-cermet anode prevents the chemical reaction between the electrolyte and nickel, thus preventing a reduction in the conductivity of the electrolyte. By optimizing the amount of Ni in the Ni-cermet and infiltrating additional catalysts such as CeO₂ and Pd, the non-ohmic ASR of the Ni-cermet anode could be optimized. This resulted in a smaller non-ohmic ASR of anode than one that was fabricated by the conventional co-sintering method. Consequently, a high power density of 790 mW/cm² at 973 K can be obtained from electrolyte-supported cells.     

Composition-tunable PtCu porous nanowires as highly active and durable catalyst for oxygen reduction reaction

To accelerate the commercialization of fuel cells, many efforts have been made to develope highly active and durable Pt-based catalyst for oxygen reduction reaction (ORR). Herein, PtCu porous nanowires (PNWs) with controllable composition are synthesized through an ultrasound-assisted galvanic replacement reaction. The porous structure, surface strain, and electronic property of PtCu PNWs are optimized by tuning composition, which can improve activity for ORR. Electrochemical tests reveal that the mass activity of Pt_0.5Cu_0.5 PNWs (Pt/Cu atomic ratio of 1:1) reaches 0.80 A mg_Pt^?1, which is about 5 times higher than that of the commercial Pt/C catalyst. Notably, the improved activity of the porous nanowire catalyst is also confirmed in the single-cell test. In addition, the large contact area with the carrier and internal interconnection structure of Pt_0.5Cu_0.5 PNWs enables them to exhibit much better durability than the commercial Pt/C catalyst and Pt_0.5Cu_0.5 nanotubes in accelerated durability test.     

Low velocity impact resistance of ceramic/polyurea composite plates: experimental study

Journal of Mechanical Science and Technology - Laminated and segmented ceramic/polyurea composite plates were fabricated by coating bulk ceramic plate and bonding ceramic tablets with polyurea,...     

Nymphoides peltatum as a novel feedstock for biomethane production via anaerobic co-digestion with waste sludge

Nymphoides peltatum (NP) is exploited as a novel feedstock for biomethane production via anaerobic co-digestion with waste sludge (WS). Batch experiments are conducted under mesophilic condition at NP/WS of 1/3, 2/2, 3/1, 0/4 and 4/0 based on volatile solids (VS). Prior to anaerobic digestion (AD), NP undergoes only natural drying and grinding. The maximum net cumulative methane yield (265.16 mL CH₄·g VS_added^?1) and the highest gross VS removal rate (56.12%) are obtained at NP/WS of 1/3. The kinetic analysis by the modified Gompertz model fit hinted that 28 days is adequate for methane recovery and co-digestion significantly accelerates the digestion rate. Synergetic effect is corroborated to exist in co-digestion due to amiable conditions in term of total ammonia nitrogen, free ammonia, pH, volatile fatty acids and total alkalinity. High-throughput 16S rRNA pyrosequencing reveals that Bacteroidetes, Firmicutes, Methanosarcina and Methanosaeta are conducive to AD of NP.     

Exposure to environmental tobacco smoke during pregnancy and infancy increased the risk of upper respiratory tract infections in infants: A birth cohort study in Wuhan,China

We aimed to evaluate the association of the exposure to environmental tobacco smoke (ETS) during pregnancy and infancy with the risk of upper respiratory tract infections (URTI) in infants based on a Chinese birth cohort study. Among 4178 infants who constituted the final study population, 46.8% experienced URTI in their first year of life. The hazard ratios (HR) and 95% confidence intervals (CI) for the risk of URTI were assessed using Cox regression models. Compared with no ETS during pregnancy, continued ETS during pregnancy was independently associated with a higher risk of URTI (HR: 1.36, 95% CI: 1.13, 1.63) after adjustment for potential confounders and also associated with earlier occurrence of URTI (log-rank P = .002). The association remained consistent across the strata defined according to maternal age, number of siblings, sex, and breastfeeding. Exposure to ETS during infancy was associated with URTI only among infants who were breastfed for less than 12 months (P for interaction < 0.05).Furthermore, infants exposed to ETS during both pregnancy and infancy showed the highest HR of 1.46 (95% CI: 1.16, 1.85) for URTI. Efforts should be made to protect pregnant women and infants from the adverse effects of indoor and outdoor ETS.     

铁矿烧结过程微细颗粒物排放行为

 采用ELPI+设备(荷电低压撞击器)对铁矿烧结过程微细颗粒物进行在线检测与采样，利用场发射扫描电子显微镜(FESEM EDS)对采集的颗粒物形貌特征进行分析，研究铁矿烧结过程中微细颗粒物的排放行为。研究结果表明，PM10大量释放集中在烧结升温段，且颗粒物质量浓度与数目浓度在粒径分布上有较大差异，其中质量浓度峰值区间为5.37～10.00 μm，数目浓度峰值区间为0.10～0.16 μm；形貌特征上，微细颗粒物呈规则的球形、方块形和片状；不同粒径物质组成差异明显，其中颗粒物中的K、Na主要以KCl和NaCl的形式存在，含量随颗粒物粒级的增大而略有降低。     

Luminescent and magnetic properties of cerium-doped yttrium aluminum garnet and yttrium iron garnet composites

Functional materials exhibiting magnetic and luminescent properties have been recognized as an emerging class of materials with great potential in advanced applications. Herein, properties of multifunctional ceramic composites consisting of two garnets, luminescent cerium-doped Y₃Al₅O₁₂ (Ce:YAG) and magnetic Y₃Fe₅O₁₂ (YIG), are reported. On increasing the sintering temperature, both the photoluminescence and saturation magnetization of the Ce:YAG-YIG composites decreased gradually because of the interdiffusion of trivalent ions such as Al³⁺ and Fe³⁺. At a constant sintering temperature of 1100?°C, the YIG contents in the composites increased, thereby causing their luminescent properties to degrade and the saturation magnetizations to increase. For application to electronics, Ce:YAG-YIG composite thin films were integrated on quartz substrates by sputtering the ceramic target. The composite thin films exhibited both magnetic and luminescent properties after annealing. These techniques facilitate the incorporation of multifunctional nanocomposites into various devices.     

Stream-Based Data Sampling Mechanism for Process Object

Process object is the instance of process. Vertexes and edges are in the graph of process object. There are different types of the object itself and the associations between object. For the large-scale data, there are many changes reflected. Recently, how to find appropriate real-time data for process object becomes a hot research topic. Data sampling is a kind of finding c hanges o f p rocess o bjects. There i s r equirements f or s ampling to be adaptive to underlying distribution of data stream. In this paper, we have proposed a adaptive data sampling mechanism to find a ppropriate d ata t o m odeling. F irst o f all, we use concept drift to make the partition of the life cycle of process object. Then, entity community detection is proposed to find changes. Finally, we propose stream-based real-time optimization of data sampling. Contributions of this paper are concept drift, community detection, and stream-based real-time computing. Experiments show the effectiveness and feasibility of our proposed adaptive data sampling mechanism for process object.     

Dansameum regulates hepatic lipogenesis and inflammation in vitro and in vivo

Food Science and Biotechnology - Although the clinical guidelines for nonalcoholic fatty liver disease (NAFLD) therapy recommended hepato-protection and exercise to reduce body weight, no...